Although many people are now using cool-running class D amplifiers to power the subs in their vehicles, those amps and the class AB or class B amps that they're using for mids and highs can generally benefit from forced air cooling. It's obvious with class AB or class B amplifiers because the heatsinks get so hot but not all of the heat in all amplifiers is transmitted to the heatsink. Many of the class D amplifiers have circuitry that operates at such high temperatures that the electrical components actually damage the circuit board over time. Even those with internal fans (fans that do not pull fresh air into the amp) are only moving around hot air and getting a bit of cool air into the amp can make the amp more reliable. Generally, you want to force cool air through the fins of the heatsink. This will most efficiently cool the amp. If the fins run the length of the heatsink and there are vents on the end of the heatsink, use a fan to force air into those vents and through the fins on the heatsink. This is the image from the Modded P45' page of the site where this was initially recommended.
If you're building your amps into an amp rack, you need to make sure that the fans in the amp rack work with and not against the fans in the amp. If the fans in the amp are blowing against the ones in the rack, it can actually reduce the air flowing through the amp and make things worse.
Most of the fans used in car audio are 'brushless' fans. Old type fans had brushes that were used to make contact with a moving commutator. This worked well enough for most applications but they produced a lot of electrical noise which could find its way into the audio signal line. In a fan that uses brushes, the voltage is applied to ever-changing windings as the armature rotates. In a brushless motor, there is no electrical contact with the spinning rotor. There are coils on the frame of the fan motor and a ring of magnets inside the fan's hub. The ring of magnets has alternating magnetic fields. There is a 'hall sensor' on the board that tells the control IC when a particular magnetic field is present and the control IC drive the coils on which pulls the rotor around. In the image below, you can see the coils, the control IC and the hall sensor (H1).
Although a brushless fan generally draws very little current (about 3 amps is the most you'll see for a 120mm fan), it's important to be aware of the current draw. The following is the label for the fan at the top of the page. As you can see, the rated voltage is 12v and the rated current draw is 0.6 amps. Compared to the current draw of amplifiers and other components, this is insignificant but as you can see, it's much more than you'd want to draw from your head unit's remote turn-on lead. That's why you almost always use a relay to drive the fan (and other accessories).
When you buy a fan, you may look for the lowest price but that's rarely going to get you the highest quality fan. Fans can be purchased with bushings (also known as sleeve bearings), one ball bearing and one bushing and with two ball bearings. If you want a fan that will work for years to come, all else being equal, the fan with two bearings will operate the longest without any maintenance. The fan below has sealed ball bearings (sealed to retain lubricant and keep out contaminants). The second image below shows the brass bushing of a cheaper fan.
The fan below is referred to as a blower, a squirrel cage fan and a centrifugal fan. This fan uses centrifugal force to move air. The air enters the round port and is forced out of the rectangular port. For their size, these fans can move a lot of air. There is a lot of discussion as to whether to call these blowers or fans. The distinction is often the ability to move air against a resistance. Fans can build very little static pressure. Blowers can build significantly more static pressure. You can tell the difference by placing your hand in front of a running fan. When you get close to a propellor type fan (one with regular blades), the air flow diminishes significantly. If you do this with a squirrel cage fan, the air flow will remain largely un-changed until you almost completely close off the output port. These can be used in place of standard fans in amp racks or for virtually any application where you need to move air. If you search for these on eBay, you should search for blower instead of squirrel cage fan. 12 volt blower seems to produce the best results.
The fan's output is rated in CFMs (Cubic Feet per Minute). Higher CFM fans move more air but they are also generally noisier so there is a tradeoff. You have to determine which is more important, air flow or a low noise level.
Noise Level:
The noise level is generally rated in either dB or sones. The dB ratings will generally have a specific reference like dBA (A-weighted which is the easiest weighting to get a low rating).THIS is the datasheet for a very high velocity (190CFM) fan. It's rated at 59dB. That's going to be a loud fan and probably not useful where the user will be in close proximity (like in a computer case). The fan used at the top of this page is an FBA12G12H1A. It's rated at about 100CFM and is relatively noisy but virtually all of the noise is from the air flowing through it. Most 120mm fans are rated at 50-80CFM.
- The wire supplying power to the relay must be protected by a fuse and the fuse must be rated to open before the wire overheats and converts your vehicle into a raging inferno.
- If there's a single wire carrying the current away from the relay to a fused distribution point (like wire 'C'), it must be the same size (or larger) as the main supply wire.
- The fuses going to the individual electrical accessories must be rated to protect thewires supplying the current to the device(s).
- If the wire feeding the individual accessories is the same as the main supply wire, the main fuse (near the power source) will protect all of the wires.
If you want your cooling fans to operate only when your amplifiers are on, it will be necessary for them to be powered only when the remote output lead has 12 volts on it (when your head unit is powered up). I would NOT recommend powering them directly from the remote power lead. It would probably be damaged by the current draw of the fans. The diagram below is a connection diagram that may be used to supply power to the fan(s). If you have multiple amplifiers and signal processors, the output from terminal 30 can also be used to supply power to the remote terminals of those devices.
- Switches
- Controlling a Relay with a Switch
- Head Unit (for info on the remote output)
In the following demo, you can change the temperature and voltage on the potentiometer. To change the voltage on the potentiometer, click above or below the arrow (on the right side of the potentiometer). This controls the reference voltage on the negative input of the op amp. Setting it lower makes the fan come on at cooler temperatures. To change the relative temperature, click on the thermometer. The value above the thermometer is an approximation of the thermistor's resistance. When the conditions are right, the relay will engage and the fan will run. Click HERE to make the demo fill this window.
If you want to use an FET to control the fan, the diagram below shows you how to connect the FET to the op amp. Keep in mind that you must insulate the tab of the FET. If the tab of the FET touches to ground, the fan will run. As an alternate FET, you can use an IRFIZ44. It's a fully insulated part and won't require an insulator. If the fan draws more than ~1/2 amp, the FET might benefit from a small heat sink.
Possible supplier: Mouser electronics http://www.mouser.com Parts list: Thermistor: 334-4227-503 Potentiometer: 531-PT10V-100k (not critical) Op amp: 511-LM358N (critical) FET: 570-IRF540 or IRFIZ44 or IRFZ44 Bipolar transistor: 625-MPSA06 (or equal) Resistors: None are critical and can likely be purchased at Radio Shack.
No comments:
Post a Comment